3/8” CA HEADER
EASY-STOP KIT
Installation Instructions
3/8” CA HEADER
WEATHER-STRIPPING SYSTEM
Easy Stop 3/8" CA Header Kit
Figure 1
remove parting-stops
Figure 2
measure upper
Figure 3
cut and fit
Figure 4
measure upper sash
Figure 5
transfer measurement
Figure 6
cut at the mark
Figure 7
measure full height
Figure 8
mark and cut bottom
Figure 9
install right side
Figure 10
install right side
Figure 11
plane for a snug fit
Figure 12
attach ropes - install
Figure 13
position of upper sash
Figure 14
detail of figure 13
Figure 15
cut 1/8” by 3/8” kerf
Figure 16
cut 1/8” by 3/8” kerf
Figure 17
install silicon flap
Figure 18
install barbed-pile
Figure 19
install lower sash
Figure 20
touch-up paint
Figure 21
finished installation
detailed Instructions
Caution!
Easy-Stop Weather stripping is “handed” Please look for the left and right side. (Standing inside the window opening, facing out).
Make a pencil mark at the center location of the meeting rail on the window jam.
Remove inside stop; remove lower sash and existing parting stop.
Measure and cut the short length (42" length for 1/2" kit or 3/8" CA Header kit) of Easy-Stop and install at top of window jam.
Instructions:
Figure 1.
Begin by removing all existing parting-stops.
(aka parting-bead)
Figure 2.
Measure for upper piece (42" stop)
Figure 3.
Cut and fit Easy-Stop head piece. Pile faces outwards.
Measure from the pencil line to the bottom of the newly installed Easy-Stop. Transfer this measurement from the center of the Easy-Stop to the top. Mark and Cut top.
Re-measure and cut the bottom of the Easy-Stop. Install.
Repeat procedure for the other side.
Figure 4.
Measure the height of the upper sash.
Figure 5.
Transfer this measurement from the middle of the pile to…
Figure 6.
…the top of Easy-Stop. Cut at the mark.
Figure 7.
Measure the full height of the right side.
Figure 8.
Mark and cut the bottom.
Figure 9.
Install right side
Figure 10.
Install right side
Figure 11.
If necessary, plane for a snug fit. If loose, glue or nail in place.
Figure 12.
Attach ropes and install upper sash.
Figure 13.
Note position of upper sash with pile.
Figure 14.
Detail of Figure 13.
Cut a 1/8” by 3/8” groove on the outside edge of the lower sash at the center of the meeting rail. Install barbed pile weather-stripping (provided).
Cut the same 1/8” by 3/8” groove at the bottom of the lower sash. Install silicone “flap” weather-stripping (provided).
Reinstall sash and inside stop moldings.
Figure 15.
For the lower sash, cut 1/8” by 3/8” kerf on the bottom. This is where the silicon flap will go.
Figure 17.
Install silicon flap on bottom.
Figure 18.
Install barbed-pile at meeting rail.
Figure 19.
Install lower sash and interior stop.
Additional tips:
To install the 3rd piece of Easy-Stop it may be necessary to slide the upper sash completely down.
Use gentle pressure to secure the Easy-Stop in the groove. Excessive pressure may cause breakage.
Scissors can be used to trim the meeting rail pile.
Easy-Stop can be secured in place by a compression fit only. May be additionally secured using acrylic caulk or brad nails.
Easy-Stop can be painted just like wood, may also be left unpainted.
Figure 20.
Complete paint and any touch-ups.
Figure 21.
You are now finished with the installation.
Easy Stop 1/2" Kit Contents
2 80” Stops
Please note: stops are “handed”.
There is a left and right-handed side.
1 42" Barbed-Pile
2 42" Silicon Flap
We provide you with the technology to do the job…
You have the experience to do it right.